- Ghost control gate opener manual

Looking for:

Ghost control gate opener manual

GHOST CONTROLS DTP1 INSTALLATION AND OWNER'S MANUAL Pdf Download | ManualsLib

Page 10 4. Proper installation of these safety instructions. This manual will guide you through the proper installation and main- tenance methods. Dual gate operations require trenching across the. When planning a system that will allow entry from a driveway so that the power cable for the second- busy road or highway, make sure the system is placed ary gate operator can be buried. Mounting location on gate and support post, column, or wall. Wooden posts should be at least 6 " x6" in size and set in concrete.

Post bracket pre-assembly. Insert the M10x1. Bolt should then go through first pivot bracket, pivot spacer, second pivot bracket, and exit bottom hole of post bracket as shown below.

Fasten a M10 washer and M10 locknut on the end of the bolt. Follow the diagram for proper notching of a round post. Once the clearances are correct, place the secondary bolt into the pivot bracket as shown. Drilling rear post bracket holes and bolting.

With the post bracket still clamped to post, mark the center of the bracket slots. Remove the bracket. Determine the mounting location for the control and battery box. The battery and control box must be located within 4 feet of each other.

Then install. NOTE Mount the control and battery box a minimum of 3 feet above the ground to keep dirt and water from damaging the control board and within 4 feet of the operator arm in order for the operator cable to reach the control box.

Connect the terminal leads of the battery harness to your battery. Insert the operator cable into the control box. Route the operator cable through the same strain relief as the battery harness cable and into the control box.

This main board shown below is located inside of the control box of your system and will be referred to in detail through the next few sections. The gate opening sequence for dual gate opener systems only is determined by DIP 4. The arm has an internal limit switch that is fixed and is not adjustable.

The arm in the fully retracted position will determine the OPEN position of the gate. Use the remote transmitter to fully retract the arm. The gate must remain in the desired open position. Install the front mount gate bracket and estate bracket on the gate by aligning the outermost hole of both brackets and inserting 1 M8 x 65mm flat washer, and 1 M8 nylon locknut through both the estate and front mount bracket, as show below. Now you can mark and drill the inner most hole on the front mount bracket, shown below.

Mark and drill center location of innermost hole F. Speaking of remotes; they are simple 3-button units that can control up to two separate Ghost Control gates. We installed the Ghost Controls Dual AutomaticThe control box can be programmed with a delay so you can get through the gate and have it close automatically behind you.

We have ours on full manual mode were you have to push the remote button to open and close the gate. Sales Department It is such a luxury to have a dual automatic gate opener. Troubleshooting Our step-by-step tool helps you get your machine working again.

The system control board includes an integrated charging circuit within it. Failure to install the 12V battery will prevent the system from working correctly. I have the heavy duty double gate, the 10 watt solar panel, the double battery holder, the key pad, and the driveway sensor, all ghost control.

The lifetime warranty with the Ghost Controls Gate Opener helps owners enjoy a secure purchase over an extended time. Logic gates use Boolean equations and switch tables.

The gate opener itself has a bi-part delay which monitors and adjusts the speed and position of the wings in order to ensure that the primary gate closes last. We are here to help. I have had it for about two years now and it is fantastic believe me. Appx cost for Ah usable: So much more dependable then any of the rest. Installation Videos Our step-by-step videos will help you to install the system easily. My Ghost gate opener just works all the time. The control box can be programmed with a delay so you can get through the gate and have it close automatically behind you.

Immigration just might be the most effective way we have to give the economy a boost Let me tell you about my friend Rod Hosilyk. Do any rust removal and touch up painting, that you might deem I have to say buying a Ghost gate Control and opener was the best decision I have made in a long time. The last possibility to look at is automatic driveway gate opener control board damage.

Update After I shot thisI researched gate openers for several months. October 13, by Mike Lee. Buy your Ghost Controls automatic gate opener today and save yourself the hassle of having to get out of your car every time! Starting at 5. Total was about Great service. As long as you follow the servicing requirements, it will last for decades. The founder of Computer Products PGate Opener: The objective for this project was to create a gate opener that I can control the logic.

Installation and troubleshooting was made easier with a LED diagnostic display, and the unit possess a solar-ready ultra-reliable system.

❿